기본 콘텐츠로 건너뛰기

Intersect Volume - Autodesk Revit Application

 Calculate intersect volume and create intersect geometry between selected elements and others.




Summary

It calculate intersect volume and create intersect geometry between selected elements and others.
Selected elements are available any shape and any category. (except mass category)
Other elements are calculated any category (except mass category) and visible in current view. (elements of revit link file are available)
Result shows list intersect elements information. (intersect element, file name, category, type, ID, intersect volume)
It can make intersect geometry to revit mass element. (mass component family)
You can get a part volume and geometry of your model. Don't need to divide model for it.


General Usage Instructions

1. Operate any 3D view.

2. Modify current 3D view visible.
 - Only visible elements are calculated intersect.
 - Revit link elements are also calculated except temporary hide. (recommend)

3. Select elements to use as targets.
 - Any shape and any category is available except mass category. 
 - Recommend make target elements by Model In-Place of generic category.

4. Operate Add-in : Add-in tab -> RevitStore panel -> IntersectVolume

5. Result list
 - Intersect elements information : intersect target element, file name, category, type, ID, intersect volume
 - Grouping : zone(target), category, type, none
 - Copy/Paste : select list and copy to clipboard (Ctrl+C) and paste to excel or notepad (Ctrl+V).

6. Error Check
 - If error is occurred, error count will be shown in the button text.
 - Click error button and paste it to notepad then error information will be shown.
 - Error is usually because of geometry incorrect, so try re-create elements more carefully for correct shape.

7. Create Geometry with revit mass family.
 - Click create button then mass family elements will be loaded and place at the position.
 - Modify visible to show mass category.


E-mail

revitstore@gmail.com

댓글

댓글 쓰기

이 블로그의 인기 게시물

 MEP Up/Down https://youtu.be/8xQfUyhq0BI To avoid a clash, MEP elements (duct, pipe, cable tray, and conduit) need to level up or down. By splitting the elements and input offset/angle value, the app redraws elements to level up or down. The app works with any language version of Autodesk® Revit®, but the command in English. It is useful for Revit HVAC, piping, and electrical modeling. It saves modeling time, improves model quality.   [Note] Available in all languages (Add-in is in English) Unit -> Offset Project Length Unit, Angle: 1~90 degrees. Fittings are referred to as Routing Preference of Type Properties. Offset Value needs enough room to place the required fittings. Convenient to use a plan view when an element is split. Insulation and lining are supported. Fabrication is not supported.

AutoFlexDuct

  App Name : AutoFlexDuct App Short Description It makes automatically flexible ducts  between ducts and air terminals. App Description It makes automatically flexible ducts  between ducts and air terminals. Air terminals are connected to nearest duct by flexduct. Multi ducts and air terminals are availible. It helps remove modeling time and improve model quality. General Usage Instructions 1. Select air terminals and ducts. 2. Select flexduct type and click Create button. 3. Each air terminals will connect to nearest duct.  * Air terminals must have only one connector.

Multi Dimensions

 This app places dimensions between multiple parallel grids, levels, or curtain grids automatically. It will help reduce your working time for documentations. Select grids, levels, or curtain wall to place aligned dimension in plan, section, or elevation view. Choose aligned dimension type and click dimension button in the app window. Click a point to place dimension on grids or levels in the view. Then multiple aligned dimension will be placed automatically. Select parallels button will help select all parallel grids. It will be useful to select not vertical or horizontal grids.